Currency:
USD
  • USD
  • EUR
  • GBP

Intake

EGR Block Off Plate

If you are going to remove you EGR valve off your 92-97 LT1 car, there is no better way than with...

If you are going to remove you EGR valve off your 92-97 LT1 car, there is no better way than with this block off plate. Proudly bearing the TPiS logo, this billet piece is machined from 6061 aluminum and anodized "Cool Grey" to last the life of your car. For motorsports use only, if the EGR system is no longe being used. Also see our 1.BOP020 Feed Tube Block Off Plate!

$14.95

EGR Block Off Plate

If you are removing the EGR valve from your 85-92 tuned port car this plate will make the job eas...

If you are removing the EGR valve from your 85-92 tuned port car this plate will make the job easy. Machined from billet aluminum and anodized "Cool Grey". For motorsports use only, when the EGR system is no longer being used. Also see our 1.BOP020 Feed Tube Block Off Plate!

$14.95

EGR Feed Block Off Plate

This Plate is designed to block off the feed tube on your 85-97 TPI/LT1 intake manifold. Each pl...

This Plate is designed to block off the feed tube on your 85-97 TPI/LT1 intake manifold. Each plate is mad of 6061 billet aluminum, anodized "Cool Grey"for a long lasting and durable part that will look great for years. For motorsports use only, when the EGR system is no longer being used. Also see our 1.BOP021 EGR Block Off for TPI cars and our 1.BOP022 EGR Block Off for LT1 cars!

$14.95

1LE Intake Duct

Originally found on the 93-97 1LE Camaro/Firebird, this part is a great way to get rid of the "sn...

Originally found on the 93-97 1LE Camaro/Firebird, this part is a great way to get rid of the "snorkel" on most factory intake ducting. This is also a great part to use on your street rod when you need to put an air filter off to the side to get it out of the way of the warm radiator air. Use a piece of 3" tubing and any aftermarket air cleaner to create your own custom intake duct. Fits all TPI and LT1/4 throttle bodies. Include air temperature sensor.

$124.95

Throttle Body AirFoil

The TPiS AirFoil is one of the first parts to start the EFI performance movement in the late 1980...

The TPiS AirFoil is one of the first parts to start the EFI performance movement in the late 1980's. This part is why TPiS exists! It is very easy to install, taking only about five minutes. When bolted in place, the AirFoil eliminates turbulence as air enters your engine's throttle body allowing it to produce more power. In a typical stock or mild engine you'll notice better throttle responce and a 5-10 hp gain and is 50 state legal.

$39.95

102mm TB Spacer

Made specifically for our 102mm throttle body to fit directly onto a TVS1900 or TVS2300 Magnuson ...

Made specifically for our 102mm throttle body to fit directly onto a TVS1900 or TVS2300 Magnuson supercharger and allow you to enlarge the opening to a full 102mm and still seal it with the provided "o"-rings.  Also works for using a 102mm throttle body on an Edelbrock E-Force or a Radik 112/122 with a J-Tube as well as any 90mm LS2/3 intake. Machined from 6061 billet aluminum and anodized titanium gray for a neutral fit in any color scheme.  Comes with two "o"-rings.

$79.95

Liquid error: Could not find asset snippets/customization-tool.liquid